Call Us : 207-994-5109

Mon – Fri: 8 am to 9 pm & Sat – Sun: 10 am to 8 pm

Lund · Mod Jon Boat Series

Lund Mod Jon Boat 1648M

The Lund Mod Jon Boat 1648M measures 15′ 8.5″, carries a 70″ beam, is rated to 30 HP, and applies the Mod Jon Boat design brief to shallow-water utility with a modified-V bow that adds a little more wave entry than a square-bow Jon while keeping a simple hunting and river layout.

Market price
$3,995 – $6,358
Estimated monthly
From $25/mo
15' 8.5"
Length
depends on engine and load
Published performance

Lund Mod Jon Boat 1648M: purpose, fit and tradeoffs

The useful way to read the Lund Mod Jon Boat 1648M is to start with the job it was built to do, not with the horsepower number.

The Mod Jon Boat 1648M is the middle choice between the Mod Jon Boat 1448M and Mod Jon Boat 1852 MT. At 15′ 8.5″ with a 70″ beam, it should appeal to buyers who have outgrown the Mod Jon Boat 1448M but cannot point to a regular reason for accepting the Mod Jon Boat 1852 MT’s larger footprint, power, and ownership cost.

Because the Mod Jon Boat 1648M is tiller-steered, the operator works from the stern and the middle of the boat stays comparatively open; that favors precise low-speed fishing and cargo room but concentrates driver, battery, and engine weight aft.

The Mod Jon Boat 1648M is aimed at this use case: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M; the Mod Jon Boat 1448M is aimed at this one: Hunters and river anglers who want a 70-inch-wide modified-bow hull in a compact 14-foot class. The deck decision should follow those two jobs before it follows horsepower or price.

For a Lund Mod Jon Boat 1648M, financing should come after this fit test.

Lund Mod Jon Boat 1648M exterior showing the hull and cockpit layout

Mod Jon Boat 1648M Specifications

Published factory figures. Confirm every dimension against the individual boat before you commit.

Dimensions and build
Beam
70"
Hull construction
aluminum flat bottom with modified-V bow
Transom
15"
Published boat weight
313 lb
Propulsion
Maximum published power
30 HP
Steering/layout
tiller
Drive type
Outboard
Used-buy focus
Cold start, service history, propeller, gearcase and tiller rigging
Fuel and range
Fuel setup
portable fuel setup
Performance reference
Varies by engine, propeller and load
Cruise burn
Measure on the exact engine and loaded boat
Range
Calculate from measured burn with a conservative reserve
Lund Mod Jon Boat 1648M hull profile and running surface

Hull construction and practical dimensions

The Mod Jon Boat 1648M starts with a 15′ 8.5″ hull and 70″ beam, but the useful hull question is what those dimensions let this Mod Jon Boat do. In this case, the Mod Jon Boat 1648M is built for rivers, marsh edges, and protected lakes where the modified-V bow is useful for current and light chop without giving up shallow-water utility.

The Mod Jon Boat 1648M is more likely to show its history on the bottom than in the upholstery. On the Mod Jon Boat 1648M, inspect the modified-V utility hull for stump or rock strikes, bank abrasion, bent spray rails, seat-base movement, transom distortion, and damage where a small trailer or pickup-bed transport has concentrated load.

For the Mod Jon Boat 1648M, the nearest physical comparison is the Mod Jon Boat 1440M, which measures 14′ on a 59″ beam and is rated to 20 HP. The Mod Jon Boat 1648M is 15′ 8.5″ on 70″ with 30 HP. The differences around the Mod Jon Boat 1648M should show up in usable room, trailer fit, and the conditions the boat can handle comfortably.

For the Mod Jon Boat 1648M, Lund lists 313 lb as the published boat-weight reference for this configuration. For the Mod Jon Boat 1648M, that is not the tow-ready number.

Power, steering and engine setup

Lund rates the Mod Jon Boat 1648M to 30 HP. For the Mod Jon Boat 1648M, the published power ceiling belongs beside the tiller layout and this intended use: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M.

The tiller position keeps the middle of the Mod Jon Boat 1648M open and puts the driver at the stern. On the Mod Jon Boat 1648M, that supports a practical cross-seat and cargo layout for hunting, river fishing, and gear hauling rather than a finished multi-species cockpit.

Power is one difference between the Mod Jon Boat 1648M and Mod Jon Boat 1440M. Lund publishes 30 HP for the Mod Jon Boat 1648M and 20 HP for the Mod Jon Boat 1440M. On the Mod Jon Boat 1648M, run both with a realistic load and compare stern trim, low-speed control, turning room and whether each outboard can reach its manufacturer-specified operating range.

For the exact outboard on a used Mod Jon Boat 1648M, begin with a cold start and service history. On the Mod Jon Boat 1648M, inspect the gearcase, skeg, propeller, mounting hardware, steering, charging output, fuel lines and rigging. Then run the Mod Jon Boat 1648M with portable fuel, normal batteries and expected gear aboard, confirming that the engine reaches its manufacturer-specified operating range without unusual vibration, ventilation or steering load.

Lund Mod Jon Boat 1648M helm, controls and outboard installation
Lund Mod Jon Boat 1648M running at a normal owner cruise

Fuel planning for the Lund Mod Jon Boat 1648M

The Mod Jon Boat 1648M should be planned around the fuel system actually installed on the boat, not around a guessed integrated-tank number. For the Mod Jon Boat 1648M, the ownership case for this boat is built around light towing and simple storage, while checking that the larger hull or higher transom still fits unimproved ramps and shallow launches.

There is no useful universal speed-and-burn figure for every Mod Jon Boat 1648M configuration. For the Mod Jon Boat 1648M, outboard choice and load matter too much.

Fuel setup is still worth comparing between the Mod Jon Boat 1648M and Mod Jon Boat 1440M. The Mod Jon Boat 1648M uses portable-fuel setup; the Mod Jon Boat 1440M uses portable-fuel setup.

On the Mod Jon Boat 1648M, keep fuel outside the loan payment when testing affordability.

How the Lund Mod Jon Boat 1648M behaves underway

Performance on the Mod Jon Boat 1648M is about shallow-water control and usable bow entry. On the Mod Jon Boat 1648M, run across river chop and boat wakes at sensible speed, then idle through the kind of tight water where the modified-V shape matters.

For the Mod Jon Boat 1648M, the Mod Jon Boat 1440M is the useful control in the comparison. The Mod Jon Boat 1440M measures 14′ with a 59″ beam and 20 HP maximum power; the Mod Jon Boat 1648M is 15′ 8.5″ with 70″ and 30 HP.

If the exact Mod Jon Boat 1648M is slow to plane, porpoises, ventilates in turns or requires unusual steering effort, separate setup from hull design before drawing a conclusion. Propeller pitch, engine height, damaged blades, battery placement, excessive stern load and an outboard that is not producing full power can all create behavior that another correctly rigged Mod Jon Boat 1648M will not share.

Lund Mod Jon Boat 1648M running in the conditions its design is meant to handle
Lund Mod Jon Boat 1648M cockpit, deck and steering layout

Cockpit, working space and helm

The deck is where the Mod Jon Boat 1648M either proves or disproves its fit. The Mod Jon Boat 1648M is aimed at this buyer and use case: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M.

On this Mod Jon Boat 1648M, fish-holding equipment is listed as center-seat gravity-fed livewell or storage provision; the capacity rating is 4 people. Those are not abstract specifications. On the Mod Jon Boat 1648M, open and operate the livewell with nearby seats or gear in normal positions and place the normal crew where they will sit, stand, fish or ride.

The tiller keeps helm hardware out of the middle of the Mod Jon Boat 1648M and preserves the open working area that defines this layout. On the Mod Jon Boat 1648M, check whether stern seating, fuel and any battery still leave the driver enough room to turn and control the outboard, then confirm that the center section remains useful with the normal tackle, decoys, coolers, camp cargo, anchors or utility gear aboard.

Walk the Mod Jon Boat 1648M and Mod Jon Boat 1440M back to back if possible. For the Mod Jon Boat 1648M, the Mod Jon Boat 1440M is aimed at this use case: River and hunting users who want a narrow 14-foot Modified Jon with better bow entry than a square-bow utility hull.

Features to inspect on the Mod Jon Boat 1648M

Use these eight Mod Jon Boat 1648M features as a hands-on checklist and verify each item on the exact boat being purchased.

Modified-V bow

On the Mod Jon Boat 1648M, inspect modified-v bow for condition, secure mounting and practical access before treating it as included value.

Four-person capacity

Use the Mod Jon Boat 1648M four-person capacity as a model-specific comparison point, then verify the related structure, labels or installed hardware on the actual boat.

Oar locks

On the Mod Jon Boat 1648M, inspect oar locks for condition, secure mounting and practical access before treating it as included value.

Center-seat storage or livewell area

On the Mod Jon Boat 1648M, run the center-seat storage or livewell area pumps, recirculation and drains where fitted, then check nearby compartments for leaks.

Stainless bow eye

On the Mod Jon Boat 1648M, inspect stainless bow eye for condition, secure mounting and practical access before treating it as included value.

Electrical, fishing and support systems

The Mod Jon Boat 1648M should remain electrically simple. On the Mod Jon Boat 1648M, follow every added wire from battery to load, looking for abrasion, unprotected connections and accessories fastened through thin aluminum without proper backing or sealing. For the Mod Jon Boat 1648M, a small utility Lund loses much of its ownership advantage when years of improvised lights, pumps and electronics turn the wiring into a troubleshooting project.

Lund lists center-seat gravity-fed livewell or storage provision for the Mod Jon Boat 1648M. For the Mod Jon Boat 1648M, fill and drain the system, run recirculation or aeration functions that are actually fitted, and look into neighboring compartments for leakage.

On the Mod Jon Boat 1648M, finish with the trailer and outboard rigging. On the Mod Jon Boat 1648M, inspect trailer lights, tires, bearings, winch, safety chains, bunks or rollers and brakes where fitted, then check the transom wiring and steering as the outboard turns from lock to lock.

Mod Jon Boat 1648M systems inspection before purchase
Mod Jon Boat 1648M on its trailer

Trailering, storage and dock fit

For the Mod Jon Boat 1648M, storage is more important than the word berthing. For the Mod Jon Boat 1648M, the reason to own this boat is light towing and simple storage, while checking that the larger hull or higher transom still fits unimproved ramps and shallow launches.

For the Mod Jon Boat 1648M, the published boat-weight reference is 313 lb. Add the selected outboard, trailer, portable fuel, batteries, electronics and normal gear before matching the Mod Jon Boat 1648M to a tow vehicle.

In New Hampshire and other freeze climates, the Mod Jon Boat 1648M also needs a winter plan that matches its equipment. On the Mod Jon Boat 1648M, protect the outboard and fuel system, manage batteries, drain pumps or plumbing that are actually fitted, and prevent water from pooling under the cover.

Typical Lund Mod Jon Boat 1648M pricing

For a relatively simple Mod Jon Boat 1648M, condition and completeness matter more than a long option list. On the Mod Jon Boat 1648M, compare hull damage, transom condition, the small outboard, portable-fuel hardware, trailer or transport setup and any owner-added electrical equipment.

On the Mod Jon Boat 1648M, keep the Mod Jon Boat 1440M visible while reading the market. The Mod Jon Boat 1648M offers 15′ 8.5″, 70″ and 30 HP; the Mod Jon Boat 1440M offers 14′, 59″ and 20 HP.

On the Mod Jon Boat 1648M, keep portable fuel, insurance, routine outboard service, winterization, storage or slip cost, trailer maintenance, batteries and electronics beside the payment.

For the Lund Mod Jon Boat 1648M, pricing and payment examples are planning tools rather than offers of credit. Actual approval, rate, term, down payment, taxes, fees and transaction requirements depend on the borrower and purchase.

Market price band
$3,995 – $6,358
Estimated monthly
From $25/mo

Illustration only and not an offer of credit.

Estimate a Lund Mod Jon Boat 1648M payment

A Lund Mod Jon Boat 1648M payment estimate is not a credit offer or approval; final financing depends on the borrower, collateral, value, condition, transaction type, rate, term, down payment, taxes, and fees.

Estimated monthly $25 Get prequalified

Illustration only and not an offer of credit. Your actual rate and term depend on credit profile, vessel age, loan amount and ownership structure.

Compare the Mod Jon Boat 1648M with nearby Lunds

The Mod Jon Boat 1648M should be cross-shopped with the Mod Jon Boat 1448M: the Mod Jon Boat 1648M is for River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M, while the Mod Jon Boat 1448M is for Hunters and river anglers who want a 70-inch-wide modified-bow hull in a compact 14-foot class.

The Mod Jon Boat 1648M should be cross-shopped with the Mod Jon Boat 1852 MT: the Mod Jon Boat 1648M is for River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M, while the Mod Jon Boat 1852 MT is for Hunting and river crews who need the largest current Mod Jon, six-person capacity, a 20-inch transom, and a 45-hp ceiling.

The Mod Jon Boat 1648M should be cross-shopped with the Jon Boat 1648: the Mod Jon Boat 1648M is for River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M, while the Jon Boat 1648 is for Owners who want the longest current square-bow Lund Jon while keeping four-person capacity and a simple 30-hp tiller package.

The cross-shop test for the Lund Mod Jon Boat 1648M is simple: when this description fits the buyer: Buyers who need six-person carrying capacity or the wider 1852 MT platform.

Mod Jon Boat 1648M compared with the rest of the range
Lund Mod Jon Boat 1648M pre-purchase inspection and transaction review

Buying a new or used Lund Mod Jon Boat 1648M

A new Mod Jon Boat 1648M purchase should be checked for hull straightness, transom specification, included seats or floor components, the exact engine or no-engine configuration, and the trailer or transport plan. For the Mod Jon Boat 1648M, these boats are simple enough that the buying decision can stay simple too.

For a used Mod Jon Boat 1648M, connect hull condition to the way this family is normally used. On the Mod Jon Boat 1648M, inspect the bottom and transom, then cold-start the outboard, review service history, test steering, electronics and pumps that are fitted, and inspect the trailer.

For the Mod Jon Boat 1648M, a private-party purchase adds paperwork that should be resolved before funds move. On the Mod Jon Boat 1648M, confirm seller ownership, lien payoff when applicable, hull identification number, engine serial number, trailer title or registration requirements and the bill of sale.

If the search keeps producing both a Mod Jon Boat 1648M and Mod Jon Boat 1440M, use the difference as a buying filter rather than shopping two nearly random boats.

Finance the right Lund

Secure a Lund Mod Jon Boat 1648M with the payment in view

A financing application makes sense after the Lund Mod Jon Boat 1648M has passed the fit test for this use case: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M.

Lund Mod Jon Boat 1648M buyer questions

The Mod Jon Boat 1648M is a strong fit for this buyer and use case: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M; it is a weaker fit for this buyer: Buyers who need six-person carrying capacity or the wider 1852 MT platform.

The Mod Jon Boat 1648M is 15′ 8.5″ long with a 70″ beam and a published boat-weight reference of 313 lb. For the Mod Jon Boat 1648M, portability still depends on the outboard, trailer or transport method, portable fuel and cargo. For the Mod Jon Boat 1648M, buyers using rough camp launches should measure the complete package rather than assuming every small aluminum boat is equally easy to move.

Lund publishes 30 HP as the maximum for the Mod Jon Boat 1648M, but the maximum is not a requirement. On the Mod Jon Boat 1648M, choose power around normal crew, gear, altitude, towing or fishing use and how quickly the boat needs to plane.

On this Mod Jon Boat 1648M, livewell equipment is listed as center-seat gravity-fed livewell or storage provision. On the Mod Jon Boat 1648M, bring the rods and tackle normally used, open the storage with seats in their normal positions and run every pump that is fitted.

The Mod Jon Boat 1648M is aimed at this profile: River anglers and hunters who want the 70-inch Mod Jon footprint with more waterline length than the 1448M; the Mod Jon Boat 1440M is aimed at this one: River and hunting users who want a narrow 14-foot Modified Jon with better bow entry than a square-bow utility hull.

On the Mod Jon Boat 1648M, inspect the hull and transom for the kind of use expected from this Mod Jon Boat, then cold-start the outboard, review service history, test steering and electrical equipment, operate pumps that are fitted and inspect the trailer or transport setup.

The Mod Jon Boat 1648M ownership budget should account for light towing and simple storage, while checking that the larger hull or higher transom still fits unimproved ramps and shallow launches.

For the Mod Jon Boat 1648M, eligible Float Finance transactions can include dealer, brokerage and private-party boat purchases. A private Mod Jon Boat 1648M purchase still needs clean ownership and lien information, hull and engine identification, trailer documentation where applicable, acceptable value and condition, and a borrower and transaction that meet lender requirements.

Secure the right Lund Mod Jon Boat 1648M

Let's Make This Easy

Tell us a little bit about yourself and the boat you are looking to finance.

Skip to content